"The Sturmpanzerwagen Oberschlesien was proposed as a lightweight, mass-produced alternative to the lumbering and expensive A7V German tank of World War 1."
Power & Performance Those special qualities that separate one land system design from another. Performance specifications presented assume optimal operating conditions for the Sturmpanzerwagen Oberschlesien Assault Tank Prototype.
1 x Argus gasoline-fueled engine developing 180 horsepower and driving a conventional track-and-wheel arrangement. Installed Power
6 mph 9 kph Road Speed
37 miles 60 km Range
Structure The physical qualities of the Sturmpanzerwagen Oberschlesien Assault Tank Prototype.
5 (MANNED) Crew
22.0 ft 6.7 meters O/A Length
7.7 ft 2.34 meters O/A Width
9.5 ft 2.9 meters O/A Height
37,997 lb 17,235 kg | 19.0 tons Weight
Armament & Ammunition Available supported armament, ammunition, and special-mission equipment featured in the design of the Sturmpanzerwagen Oberschlesien Assault Tank Prototype.
1 x 37mm OR 57mm main gun in turret.
1 x 7.92mm machine gun in hull, front-facing.
1 x 7.92mm machine gun in hull, rear-facing.
AMMUNITION: Not Available.
Variants Notable series variants as part of the Sturmpanzerwagen Oberschlesien family line.
Oberschlesien - Base Series Designation
Oberschlesien I - Initial model; two prototypes under construction by war's end.
Oberschlesien II - Proposed improved variant
The only true operational German-made combat tank of World War 1 became the ponderous Sturmpanzerwagen A7V series of which only 20 were acquired before the end of the fighting in November of 1918. The vehicle was a flawed concept from the outset, saved only by its strong armor protection. It was slow, a poor cross-country performer, required a crew of 18 or more personnel, and proved mechanically unreliable. To this was added the cost of producing the large vehicle and, as such, an alternative was sought in the form of a light-class system of more conventional tank design.
A design emerged as the "Sturmpanzerwagen Oberschlesien" - classified as an "Assault Armored Wagon" - and armed with a cannon in a traversing turret. The French were able to field their successful turreted Renault FT-17 light tanks in the war to great effect while the British preferred their turret-less lozenge-shaped steel beasts instead. As the large, turret-less A7V proved limiting for the Germans, the route of the French FT-17 was taken. The program idea sought to fill the German armored force with large stocks of fast, mobile tracked assault platforms that could be had in budget and mass-produced under the stresses of wartime. It bears mention that the German armored force, by war's end, was made up largely of captured British and French tanks.
The basic plan involved a 19 ton vehicle with a crew of five - a far cry from the 33 ton A7V with its 18-man crew. The vehicle would utilize many qualities proven in other armored vehicles of the period, particularly the filled track area comprising a portion of the hull sides and protecting the running gear to a large extent. The engine would be fitted to a rear compartment and a hull superstructure set under a 360-degree traversing turret. Vision slots would aid in situational awareness. Beyond the proposed cannon armament in the turret, a pair of 7.92mm Maxim MG08 machine guns would provide an anti-infantry measure while Armor-Piercing (AP) bullets could be used against enemy tanks in turn. Dimensions were a length of 6.7 meters, a width of 2.34 meters, and a height of 2.9 meters. Armor protection would peak at 14mm thickness.
Power was to come from an Argus gasoline-fueled engine. of 180 horsepower. This, coupled with the selected running gear arrangement and overall weight of the vehicle, would allow for road speeds of 10 miles per hour to be reached with off-road speeds reduced to about 5.5 miles per hour. Range was estimated at 35 to 37 miles. The smaller-output engine was made possible by the direction of a lightweight hull and chassis pairing - unlike the A7V that struggled mightily under its weight and underpowered propulsion system.
Work on the vehicle began in the middle of 1918 with the formal proposal handed down. Two prototypes then followed to prove the design viable though these were only partially completed before the mounting German losses of 1918 led to its collapse for the November 1918 Armistice. The pilot vehicles were being built by Oberschliesien Eisenwerk of Gleiwitz (Upper Silesia, Poland) up to October. Even before the design had been adopted for formal service, an improved model was being bandied about as the "Oberschlesien II". Regardless, none of the line ever saw the light of day due to the German surrender.
For its time, the Oberschlesien would have been a rather modern-looking combat tank though its combat effectiveness and performance can only ever be estimated. German war industry troubles would have most certainly hampered the arrival of the tank even further as a time when hundreds of British and French tanks were in use by the Allies. Certainly the German tank troubles of World War 1 were not to be repeated in World War 2.
The "Military Factory" name and MilitaryFactory.com logo are registered ® U.S. trademarks protected by all applicable domestic and international intellectual property laws. All written content, illustrations, and photography are unique to this website (unless where indicated) and not for reuse/reproduction in any form. Material presented throughout this website is for historical and entertainment value only and should not to be construed as usable for hardware restoration, maintenance, or general operation. We do not sell any of the items showcased on this site. Please direct all other inquiries to militaryfactory AT gmail.com. No A.I. was used in the generation of this content.