Aircraft / Aviation Vehicles & Artillery Small Arms Warships & Submarines Military Ranks Military Pay Chart (2024)
Land Systems / Battlefield

Carro Armato P40 (Carro Pesante P40)

Heavy Tank / Armored Fighting Vehicle [ 1940 ]

The Carro Armato P40 may have been one of the most impressive Italian war-time tanks on paper but reality limited the series in many respects.

Authored By: Staff Writer | Last Edited: 06/13/2017 | Content ©www.MilitaryFactory.com | The following text is exclusive to this site.

The Carro Armato P40 (more formally Carro Pesante P26/40 for "Heavy Tank P40") was one of the more impressive Italian tank designs of World War 2. The type was classified in Italian nomenclature as a "heavy tank" regardless of its operating weight - generally a departure from both German and Allied tank classifications of the time. She fit decent armor protection (among the best for an Italian tank) as well as a 75mm main gun. Despite its adequate qualities by Italian tank standards, the P 26/40 was generally outclassed on many levels at this stage of the war by the crop of German, Soviet, British and American tanks taking center stage. A little more than 100 P 26/40 tanks were produced before the war's end, with many of these seeing service under the German Army following Italy's surrender in 1943.

In 1940, the Italians began design work on a new 25-ton, "heavy" class infantry support tank intended to operate alongside the "M" family of medium tanks then in service. Recent fighting in the North African campaign showcased the drastic limitations of the Italian tanks then in service, prompting the Italian Army to entertain other options. The primary designation for this new tank was initially "P 75". The selected armament became a short-barreled 75mm 75/32 main gun and this was set within a traversing turret emplacement. The turret was affixed to a hull superstructure and the design was, more or less, of a highly conventional nature with long-running tracked sides - though decidedly Italian in general appearance. The originally selected engine became a diesel-fueled installation of 330 horsepower. The 75mm short-barreled gun was then upgraded to a more potent 75mm long-barrel 75/34 main gun.©MilitaryFactory.com
After the diesel engine failed to impress, the Italian Army settled on a gasoline-fueled version, forcing Ansaldo engineers back to the development board which served to delay the program. This endeavor eventually produced a gasoline-fueled engine outputting at 420 horsepower. The new tank was now designated as the "P 40" and it was in this end form that the type survived prior to the Italian Armistice. From then on, the tank would be known under the formal designation of "P 26/40" - "26" marking the vehicle's weight in tonnes while "40" denoting its year of adoption into service.

Primary manufacture of the P 26/40 was conducted out of the Ansaldo facility in Northern Italy - even after the Italian Armistice. The vehicle maintained a running length of 19 feet with a width of 9 feet, 2 inches and a height of 8 feet, 2 inches. She was crewed by four personnel that included the driver, the tank commander, the ammunition handler and a radio-operator/machine gunner. Key to this arrangement was the commander for he also doubled as the gun layer which complicated in-the-field actions. Comparable tank systems from other nations incorporated a fifth crewmember to serve as a dedicated gunner while the commander could concentrate on communicating with his crew and observing (and reacting to) battlefield developments - where seconds could spell victory or total doom for the crew. Additionally, the P 26/40 was designed with only a two-man turret system which also limited internal space - three-man turrets were now proving the norm with all new tank designs appearing elsewhere. Not only was the workload of the commander doubled in the Italian design but creature comforts were few and far between. Couple the space required for each work station with the available ammunition stores, engine compartment and transmission "hump" running along the hull floor and one can imagine the rather tight confines of the Italian design. There was no commander's cupola to provide the vehicle commander with a perched position from which to observe actions from afar which proved another tactical limitation in-the-field.

Armor protection for the P 26/40 varied about her design, ranging from 14mm at her thinnest to 60mm at her thickest facings. While something of an improvement over preceding Italian tank designs, this was rather woeful when compared to the anti-tank weaponry being fielded by Italy's enemies. Any anti-tank gun larger than 40mm was said to be able to penetrate the base armor of the P 26/40 with relative ease at this point in the war. To compound issues in the Italian design, the armor was finished in riveted construction as opposed to the much more accepted welded construction appearing on tanks elsewhere. Not only was riveted construction weaker along the plate joints (regardless of actual plate thickness), the rivets themselves could fly about the fighting compartment in response to a direct hit from enemy fire - injuring or outright killing the crew within.

Primary armament of the final P 26/40 form was a single Ansaldo-brand 75mm L/34 series main gun fitted to the traversing turret. This was backed by one 8mm Breda machine gun fitted coaxially in the turret intended for infantry defense. Some 65 projectiles of 75mm ammunition were stored aboard the tank as were 600 rounds of 8mm ammunition.

Production quality P 26/40s were powered by a single V-12 SPA 342 series diesel engine of 420 horsepower. This supplied the machine with a top road speed of 25 miles per hour (16 miles per hour off road) with an operational range of approximately 170 miles. The design was tied to a semi-elliptical leaf spring bogie suspension that allowed such values but this arrangement suffered much in terms of speed when off road compared to her contemporaries abroad.

Much had changed since design work on the P 26/40 had begun. Principally, the arrival of the Soviet T-34 Medium Tank ushered in a new era of tank design in which thick, sloped armor was the call of the day. Its success against the German lines prompted the Italians to rewrite their tank "wish list" to an extent, forcing a redesign of their P 26/40 to bring about more sloped, thick armor facings for basic ballistics protection. The design changes naturally affected the vehicle's intended weight and operating scope - now charged in the latter with engaging enemy armor head-on as opposed to supporting infantry or medium tank maneuvers. The Italian Army ordered some 1,200 P 26/40 tanks for its inventory - quite optimistic for Italian war time industry and a total that would never be met by war's end.

With the P 26/40 design in check, attention was given to evolving the existing design and chassis for other battlefield forms. The "P 43" was intended as an "up-armored" form of the base P 26/40, fielding as much as 80mm of armor thickness to contend with the growing use of anti-tank weaponry on the World War 2 battlefields. Armament considered was a 90mm main gun or a long-barreled 75mm form. The P 43bis was intended to take on a more powerful, gasoline-fueled 480 horsepower engine. At any rate, these design initiatives did not proceed past the mock-up stage before the Italian surrender.

A more promising endeavor was the "Semovente 149/40" beginning life in 1942 as a dedicated self-propelled gunnery platform intended for mobile, long-range fire support. The type was to be armed with a formidable 149mm artillery-based gun barrel in place of the turret and superstructure, consistent with Italian SPG designs of the war. However, like other P 26/40 initiatives, the Semovente 149/40 fell to naught - done in by a deteriorating war situation within Italy and lackluster trials of the single prototype completed. This pilot vehicle passed on to the Germans after the Italian surrender and was eventually captured by the Americans, ending her existence in trials at the Aberdeen Proving Grounds of Maryland, USA.

Serial production for the P 26/40 was slated for 1943. However, the Italians surrendered in September of that year, bringing about an end to her Axis support and yielding less than a handful of pre-production tanks (some sources state as many as 20 production-quality vehicles were delivered to the Italian Army). The Germans, still attempting to keep their cause alive in Italy, took over production through Ansaldo which continued into 1944 - yielding approximately 80 to 100 more of the type (under the German Army designation of Panzerkampfwagen P40 737(i)). Lack of engines meant that many were set as fixed defensive gun positions while those completed in whole saw only limited combat against the invading Allies - particularly at the Anzio beachhead. In all, however, the P 26/40 was done in by a myriad of issues - a slow-paced design and development period, a lack of a suitable proven engine from the outset, Italy' s eventual capitulation and a set of outclassed specifications and qualities. Even so, the P 26/40 remained one of the more complete Italian tank designs of the war.©MilitaryFactory.com
Note: The above text is EXCLUSIVE to the site www.MilitaryFactory.com. It is the product of many hours of research and work made possible with the help of contributors, veterans, insiders, and topic specialists. If you happen upon this text anywhere else on the internet or in print, please let us know at MilitaryFactory AT gmail DOT com so that we may take appropriate action against the offender / offending site and continue to protect this original work.


Service Year

Kingdom of Italy national flag graphic
Kingdom of Italy


National flag of modern Germany National flag of Nazi Germany National flag of Italy National flag of the Kingdom of Italy Kingdom of Italy; Nazi Germany
(OPERATORS list includes past, present, and future operators when applicable)
Fire Support / Assault / Breaching
Support allied forces through direct / in-direct fire, assault forward positions, and / or breach fortified areas of the battlefield.
Infantry Support
Support allied ground forces through weapons, inherent capabilities, and / or onboard systems.
Engage armored vehicles of similar form and function.

19.1 ft
5.82 m
9.2 ft
2.8 m
8.3 ft
2.52 m
58,246 lb
26,420 kg
29.1 tons
(Showcased structural values pertain to the base Carro Armato P40 (Carro Pesante P40) production variant. Length typically includes main gun in forward position if applicable to the design)
Powerplant: 1 x SPA 342 12-cylinder diesel engine developing 275- to 330-horsepower.
21.7 mph
(35.0 kph)
149.1 mi
(240.0 km)
(Showcased performance specifications pertain to the base Carro Armato P40 (Carro Pesante P40) production variant. Compare this entry against any other in our database)
1 x 75mm L/34 main gun (production)
1 x 8mm Breda coaxial machine gun

Supported Types

Graphical image of a tank cannon armament
Graphical image of a tank medium machine gun

(Not all weapon types may be represented in the showcase above)
65 x 75mm projectiles
600 x 8mm ammunition

Carro Armato P 26/40 - Base Series Designation
Carro Pesante P 26/40 - Formal Designation
Carro Armato P 40 - Alternative Designation
Carro Armato P 43 - Proposed Variant; fitting long-barreled 75mm main gun OR 90mm main gun.
Carro Armato P 43bis - Proposed Variant; fitting 480 horsepower gasoline-fueled engine.
Semovente 149/40 - Proposed Self-Propelled Gun; based on the chassis of the P26/40 series; single example produced.

Military lapel ribbon for the American Civil War
Military lapel ribbon for pioneering aircraft
Military lapel ribbon for the Arab-Israeli War
Military lapel ribbon for the Battle of the Bulge
Military lapel ribbon for the Battle of Kursk
Military lapel ribbon for the Cold War
Military lapel ribbon for the Falklands War
Military lapel ribbon for the Indo-Pak Wars
Military lapel ribbon for the Korean War
Military lapel ribbon for the 1991 Gulf War
Military lapel ribbon representing modern aircraft
Military lapel ribbon for the Soviet-Afghan War
Military lapel ribbon for the Spanish Civil War
Military lapel ribbon for the Ukranian-Russian War
Military lapel ribbon for the Vietnam War
Military lapel ribbon for the World War 1
Military lapel ribbon for the World War 2
Military lapel ribbon for the Yom Kippur War
Military lapel ribbon for experimental military vehicles

Ribbon graphics not necessarily indicative of actual historical campaign ribbons. Ribbons are clickable to their respective campaigns / operations.

Images Gallery

1 / 1
Image of the Carro Armato P40 (Carro Pesante P40)
Front left side view of the Carro Armato P26/40 heavy tank

Disclaimer | Privacy Policy | Cookies

2024 Military Pay Chart Military Ranks DoD Dictionary Conversion Calculators Military Alphabet Code Military Map Symbols

The "Military Factory" name and MilitaryFactory.com logo are registered ® U.S. trademarks protected by all applicable domestic and international intellectual property laws. All written content, illustrations, and photography are unique to this website (unless where indicated) and not for reuse/reproduction in any form. Material presented throughout this website is for historical and entertainment value only and should not to be construed as usable for hardware restoration, maintenance, or general operation. We do not sell any of the items showcased on this site. Please direct all other inquiries to militaryfactory AT gmail.com. No A.I. was used in the generation of this content; site is 100% curated by humans.

Part of a network of sites that includes GlobalFirepower, a data-driven property used in ranking the top military powers of the world, WDMMA.org (World Directory of Modern Military Aircraft), WDMMW.org (World Directory of Modern Military Warships), SR71blackbird.org, detailing the history of the world's most iconic spyplane, and MilitaryRibbons.info, cataloguing military medals and ribbons. Special Interest: RailRoad Junction, the locomotive encyclopedia.

©2023 www.MilitaryFactory.com • All Rights Reserved • Content ©2003-2023 (20yrs)