Military Factory logo
Icon of a dollar sign
Icon of military officer saluting
Icon of F-15 Eagle military combat fighter aircraft
Icon of Abrams Main Battle Tank
Icon of AK-47 assault rifle
Icon of navy warships

Richmond Armory Model 1855 (Richmond Rifle)

Percussion Cap, Single-Shot, Muzzle-Loaded Rifle

Richmond Armory Model 1855 (Richmond Rifle)

Percussion Cap, Single-Shot, Muzzle-Loaded Rifle

OVERVIEW
SPECIFICATIONS
VARIANTS
HISTORY
MEDIA
OVERVIEW



The Richmond Rifle was nothing more than a Confederate copy of the Springfield Model 1855 rifle - manufactured on stolen Union equipment.
National Flag Graphic
ORIGIN: Confederate States
YEAR: 1862
MANUFACTURER(S): Richmond Armory - Confederate States
OPERATORS: Confederate States
SPECIFICATIONS



Common measurements, and their respective conversions, are shown when possible. Calibers listed may be model/chambering dependent.
ACTION: Percussion Cap; Muzzle-Loaded; Single-Shot
CALIBER(S): .58 Minie Ball
LENGTH (OVERALL): 1,422 millimeters (55.98 inches)
LENGTH (BARREL): 1,015 millimeters (39.96 inches)
WEIGHT (UNLOADED): 9.92 pounds (4.50 kilograms)
SIGHTS: Iron Front and Rear
MUZZLE VELOCITY: 1,100 feet-per-second (335 meters-per-second)
RATE-OF-FIRE: 2 rounds-per-minute
RANGE (EFFECTIVE): 1,800 feet (549 meters; 600 yards)
VARIANTS



Series Model Variants
• Richmond Rifle - Base Series Name


HISTORY



Detailing the development and operational history of the Richmond Armory Model 1855 (Richmond Rifle) Percussion Cap, Single-Shot, Muzzle-Loaded Rifle.  Entry last updated on 9/13/2016. Authored by Staff Writer. Content ©www.MilitaryFactory.com.
The capture of machinery and tooling in the April 1861 raid by Confederate forces at Harpers Ferry granted the South with useful gun-making equipment that was badly needed. Some of the equipment ended in Fayetteville, North Carolina and some in the Confederate capital of Richmond, Virginia. The result was two rifles developed to the form and function of the Springfield Model 1855 (detailed elsewhere on this site). Depending on their origination, the guns came to be known as either "Fayetteville Rifles" or "Richmond Rifles".

Production of Richmond Rifles began in October of 1962 and more or less following the lines dictated by the original Springfield. However, the original gun called for support of the Maynard Tape Primer system to speed reloading of the percussion cap-based action. This feature was omitted in the Richmond Rifle for expediency and simplicity but the lockplate of some early models still retained the distinctive "hump" (Type I and Type II guns with slight variations between them). Only in March of 1862 was the die revised and the hump subsequently deleted (Type III rifles). A brass nosecap as fitted at the forend of the stock and original iron-based butt plates were superseded by brass-based ones. The patchbox in the stock was removed and different sighting gear fitted over the rifle.

The rifle fired the .58 Minie Ball and reloading was from the muzzle. A trained operator could expect to shoot two to three rounds per minute with some accuracy out to 600 yards thanks to the rifled barrel. Muzzle velocity was 1,000 to 1,200 feet per second.

Before the end of the year, the Richmond facility began manufacture of a shortened version of the Richmond Rifle to serve in the carbine role. This form had the barrel length reduced to 25-inches (from 40-inches). Shortages of wood also dictated that the original 56-inch long gun was also reduced in length to save on materials and this produced a 49-inch form with 33-inch barrel length.

Richmond Rifles were manufactured at the Richmond Armory from 1861 until early-1865. Some were reportedly also based on the Springfield Model 1863 rifle design.